Switch Ball – Bender Back Style
In this video, Steve K. will attempt to teach how to make a switch ball with the bender back style.
Go the Bender Back way!
There are a lot of ways to make a wig wag on some lined tubing. This is the last technique I learned to do the wig wag. I get to show you how now, it took me about 8 years to find this method. Oh what YouTube has done for us all! I love this way because I can get really tight wig wags. It also goes way faster than any other technique I have used. Do you need to know the other ways to make a wig wag switch ball? HELL YES you do. They make it so you can do other patterns not able to do with the bender back style. But if you are looking for tight clean wig wags, this is the way to do it I feel most of the time. In the video you will see how tight you can make them. Always remember the smaller the diameter tubing the tighter the wig wags will be also.
The Bender Back Glass Technique-
To do this I recommend first you learn to pull your own color. It’s like a right of passage to know one thing before you move on. But either way, here you go on how to do this amazing glass blowing technique.
- Start out with a nice piece of lined color. If it is too thin you can for sure pull this off, but it makes it more difficult. Thicker is better for this technique. I start with a piece of lined tubing about 70mm-100mm long. I try to go for 7 to 9 points when I make these. Then I do the spin on the end. You will want to weld this to a blow tube, I like 12mm tubing to use. Now close off the other end if it is not closed off and then weld up a rod, make sure this is a good weld, as it can cool and crack later.
- Now you have control of this piece of colored tubing. Start out now with a really small flame and heat this lined tubing up in the center. Once you can feel that you could bend the tubing you are about right with the heat. Now you will want to bend the glass. This is for sure strange, but you will spin it in a jerking motion as you have to spin both sides at the same time and same amount. This pushes and pulls the glass making the bend in the color. Its so NEAT! Do not heat the glass up too much, just enough to bend the glass. It is ok if you get some deviance will go away as you make the ball.
- Repeat this over and over till you have the full tube of color wig waged up. I like to leave about 1/2 inch on each side so I have some glass to spin up, I like the wig wag with spin, it sexy right!!
- Now you will do your termination. I do not care what way I spin these, I just spin them in the opposite direction of the last wig wag. If you try to go with the wig wag you will get like a stair step effect. If this is what you want then go this way, if not go the opposite way. Spin and pull this down so it is smooth. Now you have a like spun cone, get this end thin and pull off the tip so it is just a little thing. Now melt this down evenly.
- Now you will pop a hole in the side of the ball you are making. I prefer to go small, then make the hole bigger. I try really hard not to let it get too wet. I want the color and clear to be centered in the glass so when I put the next switch ball on it the clear and color line up. If the color melts out to the outside you can have an adultered color come out and that will not be good. You always want the clear on the outside with the color on the inside.
- With your hole in the side, you will punty up to it and remove the blow tube. While you are removing the blow tube you will want to give it that spin to match the other spin. Use a Sophi or bent glass so you can blow out this cone. Be careful not to let it gather too much as the colors will over lap each other and make a bad termination. Its all about the termination here yall!!
- Repeat this on another switch ball and put the hole on the opposite color so you can put one to a blow tube and then put the two wig wag switch balls together.
- Repeat again and again until you are great at this. It takes time and more time.
Learn on the Daily Motion channel at Elev8 Presents and also our Entertainment site Elev8 Presents.com.
Sorry, YouTube deleted our content. We are recreating this video and it will be ASAP. Thank you for your patience!